Posts Tagged ‘sc10’

JConcepts- B4, T4 & SC10 2.5mm carbon fiber steering rack

It’s hard to make an improvement to the race proven B4.2 buggy.   However, JConcepts has pulled another option out from under their design sleeves with a genuine Carbon Fiber steering rack and hardware kit.     In the stock trim, the B4.2 steering swings a molded plastic steering rack supported by bushings.      The JConcepts alternative uses the […]

JConcepts – SC10, T4 (F&R) and B4 (rear) anti-roll bar kit

Control is everything and especially in truck racing where the center of gravity is high and the trucks are narrow in width. Having a stable and race-able platform is the key to success and JConcepts has made that easier for racers with a Team Associated SC10, T4 or B4 vehicle. The JConcepts anti-roll-bar kit is […]

Associated SC10 Refresh with AVID RC & Viper

This is my Team Associated SC10 2wd Short Course truck. It started life as a standard kit (not the Factory Team). I’ve done minor upgrades through the couple years I’ve owned it and adding a few more today. With as little as I run 2wd SC, I find it hard to justify a new SC10.2 […]

New Releases from JConcepts

JConcepts has released a few new items today.   JConcepts – SC10 Carbon Fiber front body mount Part # – 2233 UPC Code – 845937008817 Retail price – $20.00 (Fits – Team Associated SC10 vehicles) JConcepts adds another top quality carbon fiber accessory to the already hefty list for the SC10 line of vehicles with […]

JConcepts new B4.1, T4.1 and SC10 front axle

One of the best upgrades you can make to the Team Associated line of vehicles is a conversion to 12mm hex wheels. JConcepts has been on top of this conversion since its introduction with hex adapters and Mono wheels.  A critical point of the conversion revolves around the front axle and surrounding geometry. Within the […]

AVID SC10 12mm Hex Conversion Kit

Upgrade your SC10 FT or SC10 RTR to use 12mm hex wheels with the pre-assembled AVID SC10 12mm Hex Conversion Kit.  Using genuine Team Associated steering blocks and front axles,  AVID pre-assembled the steering blocks with their 12mm front clamping hex adapters, Revolution bearings, and solid axle pins.   No more hunting around for all the […]

NEW Team Associated SC10B RS RTR !!

SC10B Race-Spec 1:10 Scale Ready-to-Run 2WD Electric Off Road Race Buggy Team Associated‘s SC10B Race Spec Ready-To-Run is a short course pro buggy based on the three-time undefeated R.O.A.R. National Championship winning SC10 truck chassis.Loaded with high performance features, the incredibly realistic SC10B comes equipped with a factory finished short course pro buggy body, roll […]

Triad Slipper Clutch and Spur Gears for B4.1, B44.1 and TLR 22

The AVID Triad Slipper Clutch represents the next-generation in slipper clutch design. The Triad slipper utilizes 3 drive plates and 3 slipper pads to make a compact clutch that has better driving feel, lasts longer, and has a lower rotating inertia. A slipper clutch must balance three connected elements: Torque, Pressure, and Friction. AVID has […]

Carbon Fiber Hub Towers for B4.1, B44.1, T4.1, SC10

The new AVID carbon fiber hub towers are a great upgrade for any Associated racer running blue aluminum rear hubs on their B4.1, B44.1, T4.1 or SC10. Features are: 2-in-1 High and Low Outer pivot locations: Without changing parts, racers can run the standard kit upper link location “A” tower, or try dropping the outer […]

AVID’s New Precision Springs for 10th scale Buggy and Truck

Next week on Tuesday, April 24, AVID is bringing you the utmost in precision and performance with new springs for 10th scale 12mm big-bore shocks. AVID precision springs offer several advantages over conventional shock springs: 1. The labels are custom printed to show the average spring rate (in lb/in) for each batch of springs after […]

Powered by WordPress